Free Cisco 200-301 Exam Questions and Answer from Training Expert Pass4SureQuiz
Top Cisco 200-301 Courses Online
What Skills Does It Measure?
The Cisco 200-301 test is designed to gage the following skills:
- IP Connectivity (25%);
- IP Services (10%);
- Security Fundamentals (15%);
- Network Access (20%).
NEW QUESTION 120
What is the function of a controller in controller-based networking?
- A. It is a pair of core routers that maintain all routing decisions for a campus
- B. It serves as the centralized management point of an SDN architecture.
- C. It is the card on a core router that maintains all routing decisions for a campus.
- D. It centralizes the data plane for the network.
Answer: B
NEW QUESTION 121
Which two protocols are used by bridges and/or switches to prevent loops in a layer 2 network? (Choose two.)
- A. 802.1d
- B. STP
- C. VTP
- D. SAP
- E. 802.1q
Answer: A,B
NEW QUESTION 122
Which command can you enter to verify that a BGP connection to a remote device is established?
- A. show ip bgp summary
- B. show ip community-list
- C. show ip route
- D. show ip bgp paths
Answer: A
NEW QUESTION 123
Refer to the exhibit.
An engineer is tasked with verifying network configuration parameters on a client workstation to report back to the team lead. Drag and drop the node identifiers from the left onto the network parameters on the right.
Answer:
Explanation:
NEW QUESTION 124
Drag and Drop Question
Refer to the exhibit. Drag and drop the networking parameters from the left on to the correct values on the right.
Answer:
Explanation:
Explanation:
The "ip route" and "ip addr show eth1" are Linux commands.
+ "ip route": display the routing table
+ "ip addr show eth1": get depth information (only on eth1 interface) about your network interfaces like IP Address, MAC Address information
NEW QUESTION 125
Drag and drop the network protocols from the left onto the correct transport services on the right.
Answer:
Explanation:
NEW QUESTION 126
Drag and drop the functions from the left onto the correct network components on the right
Answer:
Explanation:
NEW QUESTION 127
A device detects two stations transmitting frames at the same time. This condition occurs after the first 64 bytes of the frame is received interface counter increments?
- A. late collision
- B. runt
- C. CRC
- D. collision
Answer: A
NEW QUESTION 128 
Refer to the exhibit. An engineer must add a subnet for a new office that will add 20 users to the network.
Which IPv4 network and subnet mask combination does the engineer assign to minimize wasting addresses?
- A. 10.10.225.32 255.255.255.224
- B. 10.10.225.32 255.255.255.240
- C. 10.10.225.48 255.255.255.240
- D. 10.10.225.48 255.255.255.224
Answer: A
NEW QUESTION 129
Drag and Drop Question
Refer to the exhibit. Drag and drop the networking parameters from the left on to the correct values on the right.
Select and Place:
Answer:
Explanation:
Explanation:
The "ip route" and "ip addr show eth1" are Linux commands.
+ "ip route": display the routing table
+ "ip addr show eth1": get depth information (only on eth1 interface) about your network interfaces like IP Address, MAC Address information
NEW QUESTION 130
Your company network security policy requires that all network traffic be tunneled to the corporate office. End users must be able to access local LAN resources when they connect to the corporate network. Which two configurations do you implement in Cisco AnyConnect? (Choose two.)
- A. Client Bypass Protocol
- B. tunnel all
- C. split-exclude tunneling
- D. local LAN access
- E. static routes
Answer: B,D
NEW QUESTION 131
Refer to the exhibit.
An engineer configured the New York router with state routes that point to the Atlanta and Washington sites.
When command must be configured on the Atlanta and Washington routers so that both sites are able to reach the loopback2 interface on the New York router?
- A. ipv6 route ::/0 Serial 0/0/1
- B. ipv6 route ::/0 2000::2
- C. ip route 0.0.0.0.0.0.0.0 Serial 0/0/0
- D. ipv6 route 0/0 Serial 0/0/0
- E. ipv6 route ::/0 Serial 0/0/0
Answer: E
NEW QUESTION 132
Refer to the exhibit.
An engineer is configuring the router to provide static NAT for the webserver Drag and drop the configuration commands from the left onto the letters that correspond to its position in the configuration on the right.
Answer:
Explanation:
NEW QUESTION 133 
Refer to the exhibit. How does the router manage traffic to 192.168.12.16?
- A. It chooses the EIGRP route because it has the lowest administrative distance.
- B. It load-balances traffic between all three routes.
- C. It chooses the OSPF route because it has the longest prefix inclusive of the destination address.
- D. It selects the RIP route because it has the longest prefix inclusive of the destination address.
Answer: C
Explanation:
Section: IP Connectivity
NEW QUESTION 134
What are two functions of an SDN controller? (Choose two)
- A. protecting against DDoS attacks
- B. managing the topology
- C. Layer 2 forwarding
- D. coordinating VTNs
- E. tracking hosts
Answer: B,D
NEW QUESTION 135 
Refer to the exhibit. How does SW2 interact with other switches in this VTP domain?
- A. It forwards only the VTP advertisements that it receives on its trunk ports.
- B. It transmits and processes VTP updates from any VTP clients on the network on its trunk ports.
- C. It receives updates from all VTP servers and forwards all locally configured VLANs out all trunk ports.
- D. It processes VTP updates from any VTP clients on the network on its access ports.
Answer: A
Explanation:
Section: Network Access
Explanation:
The VTP mode of SW2 is transparent so it only forwards the VTP updates it receives to its trunk links without processing them.
Reference: https://www.cisco.com/c/en/us/support/docs/lan-switching/vtp/10558-21.html
NEW QUESTION 136
......
New (2022) Cisco 200-301 Exam Dumps: https://www.pass4surequiz.com/200-301-exam-quiz.html
200-301 Practice Dumps - Verified By Pass4SureQuiz Updated 216 Questions: https://drive.google.com/open?id=13d6e6tq8zfVqeyQZ_hC3JHaFZq74qNHV