New 2021 HPE6-A45 exam questions Welcome to download the newest Pass4SureQuiz HPE6-A45 PDF dumps (170 Q&As)
P.S. Free 2021 Aruba Certified Switching Professional (ACSP) V1 HPE6-A45 dumps are available on Google Drive shared by Pass4SureQuiz
NEW QUESTION 19
Refer to the exhibits.
Exhibit 1
Exhibit 2
The exhibits show the current operational state for routes on Switch-3. The company wants Switch-3 to send all traffic to 172.16.0.0/16 through Switch-2.
Which single configuration change creates the desired behavior?
- A. Set a cost of 5 in the router ospf area 0.0.0.1 stub command on Switch-1.
- B. Change the OSPF external metric type to 2 on Switch-1 and Switch-2.
- C. Set a cost of 15 in the redistribute static command on Switch-2.
- D. Change the OSPF external metric type to 1 on Switch-1 and Switch-3.
Answer: C
NEW QUESTION 20
A customer wants access layer switches that support routing, ACLs, backplane stacking, and Smart rate ports.
The customer asks about Aruba 5400R z 12 switches.
Which Aruba Switch model would better meet the customer's requirements?
- A. 0
- B. 1
- C. 2930F
- D. 2
Answer: B
NEW QUESTION 21
Refer to the exhibit.
Endpoints in VLAN 2 connect directly to this switch. These devices should only be able to send DHCP, DNS, HTTP, and HTTPS traffic. However, they are able to send any traffic. Based on the exhibit, what is the issue?
- A. The ACL lacks a deny ip any any statement at the end.
- B. The switch does not have an IP address on VLAN 2.
- C. The ACL is applied in the wrong direction.
- D. The name of the ACL applied to VLAN 2 is incorrect.
Answer: D
NEW QUESTION 22
The security policy for the company requires that switches use SNMPv3 and accept all read-only SNMPv2c messages.
The network administrator enables SNMPv3.
Which additional action should the network administrator take to company with this policy?
- A. Disable SNMPv1/v2c
- B. Enable SNMPv3 restricted mode
- C. Enable SNMPv3 only operation
- D. Disable SNMPv3 inform timeouts
Answer: D
NEW QUESTION 23
Refer to the exhibits.
The network administrator enters the commands shown in Exhibit 2, and Switch-1 and Switch-2 exchange keepalive messages. What is the expected behavior if Switch-1 later fails to receive keepalive messages from Switch-2?
- A. After two consecutive missed keep-alive packets, Switch-1 sends SNMP traps, and Link 1 stays up until the issue is fixed.
- B. Switch-1 disables interface 1 for 10 seconds and then re-enables it. The interface continues to be re-enabled and disabled every 10 seconds until the issue is fixed.
- C. Switch-1 disables interface 1 for 10 seconds, and then re-enables it. The same process repeats twice. If the issue persists, the switch disables the interface permanently.
- D. After two consecutive missed keep-alive packets, Switch-1 disables interface 1, and the interface stays disabled until the issue is fixed.
Answer: D
NEW QUESTION 24
Refer to the exhibit.
What must the network administrator do on Switch-1 to enable this switch to advertise 192.0.2.0/24 to the router at 192.168.1.1?
- A. Enable eBGP multihop to the 192.168.1.1 neighbor.
- B. Redistribute OSPF routes into the BGP process
- C. Enter a static route to 192.0.2.0/24 to the black hole.
- D. Enter the network 192.168.1.0/24 command in the BGP context.
Answer: C
NEW QUESTION 25
Refer to the exhibit.
Switch-1 and Switch-2 connect on interface A23. The switches experience a connectivity issue. The network administrator sees that both switches show this interface as up. The administrator sees the output shown in the exhibit on Switch-1.
What is a typical issue that could cause this output?
- A. asymmetric routing introduced by a routing protocol
- B. a jumbo frame mismatch
- C. mismatched subnet mask on the VLAN for the link
- D. an issue with VLAN mismatch
Answer: A
NEW QUESTION 26
Refer to the exhibit.
The network administrator wants to summarize routes as much as possible in between areas. What is the correct range to specify for the router OSPF Area 2 command on Switch-2?
- A. 10.0.0.0/20
- B. 10.0.16.0/21
- C. 10.0.0.0/21
- D. 10.0.8.0/21
Answer: B
NEW QUESTION 27
Refer to the exhibit.
The network administrator wants to summarize routes as much as possible in between areas. What is the correct range to specify for the router OSPF Area 2 command on Switch-2?
- A. 10.0.0.0/20
- B. 10.0.16.0/21
- C. 10.0.0.0/21
- D. 10.0.8.0/21
Answer: B
NEW QUESTION 28
Refer to the exhibit.
An administrator created a backplane stack with the plug-and-play method, and did not alter the default backplane stacking settings. Later, two backplane stacking links failed, as shown in the exhibit.
What happens to the backplane stack after the failures?
- A. The fragment that contains the commander operates at Layer 2 and layer 3, and the other fragment operates at layer 2 only.
- B. The fragment that contains the commander remains active, and the fragment with the standby member is disabled.
- C. The standby becomes the commander of its fragment, which remains active. The fragment with the commander becomes inactive.
- D. The standby becomes the commander of its fragment. Both fragments remain active and operate at both Layer 2 and Layer 3.
Answer: D
NEW QUESTION 29
A customer wants access layer switches that support routing. ACLs, VSF stacking, and SFP+. Which Aruba switch model meets the customer's requirements?
- A. 0
- B. 1
- C. 2930F
- D. 2
Answer: C
NEW QUESTION 30
A company wants to implement 802.1X authentication to authenticate client devices on AOS-Switch ports. The company has a RADIUS server that uses PEAP mschap-v2 for the authentication method. What is one task administrators should complete before they implement the plan?
- A. Install personal certificates on client devices.
- B. Set up an isolated VLAN in the network for the 802.1X communications.
- C. Ensure client device trust the RADIUS server certificate.
- D. Configure DHCP services on the AOS-Switches for pre-authenticated clients.
Answer: D
NEW QUESTION 31
A company has AOS-Switches deployed at sites with inexperienced IT staff. The main office network administrators want to track if configurations change on branch switches.
What should be set up for this purpose?
- A. an RMON alarm
- B. an SNMP trap
- C. an IP SLA profile
- D. an auto-config server
Answer: B
NEW QUESTION 32
Refer to the exhibit.
AOS-Switches will enforce 802.1X authentication on edge ports. The company has two RADIUS servers, which are meant to provide redundancy and load sharing of requests.
The exhibit shows the planned RADIUS settings to deploy to the switches.
What should customers understand about this plan?
- A. AOS switches do not support two RADIUS servers for redundancy, instead, a secondary authentication method is required.
- B. Each RADIUS server must use a unique port number for the authentication and dynamic authorization port.
- C. Each AOS-Switch will send all RADIUS requests to the first server on the list unless that server becomes unreachable.
- D. Dynamic authentication is only permitted on one of the RADIUS servers and must be removed from the other.
Answer: C
NEW QUESTION 33
What is a reason to implement port security on an AOS-Switch?
- A. to control management access to the switch CLI based on device, as well as user credentials
- B. to filter traffic at the edge, based on multiple criteria in the MAC header
- C. to enhance the security of an 802.1X solution
- D. to simplify provisioning for devices such as IP phones or printers
Answer: C
NEW QUESTION 34
......
HPE6-A45 exam questions from Pass4SureQuiz dumps: https://www.pass4surequiz.com/HPE6-A45-exam-quiz.html (170 Q&As)